When installing reducer, attention shall be paid to the alignment of transmission center axis, and the error shall not be greater than the compensation amount of the coupling used. Good alignment can prolong service life and obtain ideal transmission efficiency.

 How to reduce motor speed with gears

When installing the transmission parts on the output shaft, it is not allowed to strike with a hammer. Usually, the internal thread of the assembly fixture and shaft end is used to press the transmission parts with bolts, otherwise it may cause damage to the internal parts of the reducer. It is better not to use rigid fixed coupling, because this kind of coupling installation is improper, will cause unnecessary external load, so as to cause the early damage of the bearing, and even cause the fracture of the output shaft when serious.

 

The reducer shall be firmly installed on a stable foundation or base, and the oil in the oil drain groove shall be removed, and the cooling air circulation shall be smooth. The foundation is unreliable, which may cause vibration and noise when running, and cause bearing and gear damage. When the transmission connection has the protrusion or USES the gear, the chain wheel transmission, should consider to install the protective device, when the output shaft bears the big radial load, should choose the strengthened type.

How to reduce motor speed with gears

Gear reducer motor is motor and reducer and two for one abbreviation, gear reducer as its name suggests, is to use different number of n sets of gears, the motor shaft speed down to the speed you need, gear reducer motor can fully cooperate with the rotation encoder.How to use and install gear reducer motor, be sure to follow the following operation!

How to use and install gear motor?

Steps/methods

1. When installing reducer, attention shall be paid to the alignment of transmission center axis, and the error shall not be greater than the compensation amount of the coupling used.Good alignment can prolong service life and obtain ideal transmission efficiency.

2. When installing the transmission parts on the output shaft, it is not allowed to strike with a hammer. Usually, the internal thread of the assembly fixture and shaft end is used to press the transmission parts with bolts, otherwise it may cause damage to the internal parts of the reducer.It is better not to use rigid fixed coupling, because this kind of coupling installation is improper, will cause unnecessary external load, so as to cause the early damage of the bearing, and even cause the fracture of the output shaft when serious.

How to reduce motor speed with gears

3. The reducer shall be firmly installed on a stable foundation or base, and the oil in the oil drain groove shall be removed, and the cooling air circulation shall be smooth.The foundation is unreliable, which may cause vibration and noise when running, and cause bearing and gear damage.When the transmission connection has the protrusion or USES the gear, the chain wheel transmission, should consider to install the protective device, when the output shaft bears the big radial load, should choose the strengthened type.

 How to reduce motor speed with gears

4. Install the device according to the regulations to ensure that the staff can get close to the oil mark, air plug and oil drain plug conveniently.After installation, it shall check the accuracy of the installation position in order, and the reliability of the compression of each fastener. After installation, it shall be able to rotate flexibly.The reducer is lubricated by splashing oil pool. Before operation, the user should remove the screw plug of the air hole and replace it with an air plug.According to different installation positions, and open the oil level plug screw to check the height of the oil level line. Add oil from the oil level plug until the lubricating oil overflowed from the oil level plug hole.Operation should be smooth, no impact, vibration, noise and oil leakage phenomenon, abnormal should be promptly eliminated.

Christine Zhu ( Sales Department; Miss. )          
NER GROUP CO.,LIMITED                            
Tel:+86-535-6330966
Mobile:+86-13688909643
https://
www.bonwaygroup.com/
https://twitter.com/gearboxmotor
https://www.facebook.com/ner.sogears.1
Viber/Line/Whatsapp/Wechat: 008613688909643
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.;  
Skype ID: This email address is being protected from spambots. You need JavaScript enabled to view it.
Factory Add: 
No.5 Wanshoushan Road, Yantai, Shandong Province, China (264006)